Home > Product > Globe Valve > GV400 Series 2/2ways Piston Controlled Flat-seat Valve (Big Port)
2ways piston controlled flat-seat valve
  • 2ways piston controlled flat-seat valve

2ways piston controlled flat-seat valve

Characteristics:
1) GV400 Series Plunger pilot angle seat valve is propelled by piston actuator, either single acting or double acting.Actuators are made of three different materials, applicable to different working temperature.
2) 2/2 ways stainless steel valve with big flow capacity, and V type seals ensure reliable and effective sealing.
3) Maintenance free, compatible with various accessories. Direction indicating, stroke limiting or manual switching can be achieved conveniently.
4) Flange ends and weld ends are optional.
5) Valve body material 304/316 optional.
6) Upstream & downsteam in flow direction optional.

Inquire Now
  • Specification
  • Dimension

Upsteam DN80-100 G3~G4
Material of bodyCasting S.S. 304/316
Material of ActuatorPA (S.S actuator is required)
SealingPTFE (NBR, FKM, EPDM be required)
Ambient and fluid

Air,water, oil(50CST below),steam,alcohol, fuel, saline solution,

aqueous alkali,organic solvent

ViscosityMax.600mm2/s
Packing glands sealPTFE
Medium Temperature-10 to +180℃ with PTFE seal

Ambient Temperature 

PA actuator

Actuator size below 125mm

-10 to +60℃
Operating MediumNeutral gas, Air
Max.pressure of pilot valve
Actuator size 100mm
Actuator size 125mm

PA 10bar
PA 7bar

* 1 kgf/cm2 = 1 bar = 0.1 Mpa = 100KPa = 14.5psi


Installation of the valve:

1) Installation in any orientation but preferably with the actuator above.

Note: Clean piping from contamination!!!
2) Before attaching the valve housing, make sure the piping is aligned!
3) If the housing is to be welded on, make absolutely sure that the actuator is removed before hand.

Devices with Approval DIN EN 161: According to DIN EN 161"Automatic Shut-off Valves for Gas
burners and Gas applicances", a dirt trap must be connected upstream of valve. In order to maintain approval, also with stainless steel housing, upsteam of the valve.

Procedure:
1. Remove the pneumatic supply and the electrical connection(if a pilot valve is attached).
2. Control function A:Pressurize the lower control port of actuator with compressed air(6bar), so that the valve disk is lifted from the valve seat and it not damaged.
Control function B and I: No compressed air must be applied.
3. Remove the actuator in the open valve position by unscrewing the threaded nipple from the housing.
4. Before reinstalling the actuator( in the open valve position), grease the nipple thread with stainless steel lubricant.
5.Replace the graphite seal.
ATTENTION! For specical applications such as for oxygen and analysis,use only the approved lubricants
6. After tightening the threaded nipple, align the control ports by turning the actuator.
ATTENTION!: During this operation, the valve must be in the open position.
NOTE: For applications in aggressive media, we recommend attaching all free penuamtic connections  to a pneumatic hose whose other end lies in a neutral atmostphere.


Pneuamtic installation:

Control medium: Air
1) Direct connection to the piston control valve.
with control function A, at the lower connection of actuator with G1/4 thread.
with control function B, at the upper connection of actuator with G1/4 thread.
with control function I, at the upper and lower connection of actuator with G1/4 thread.

2) Connection via pilot valves.
Mount the solenoid valve Type 4M410-15 with NAMUR Adapter and banjo bolt on the actuator for double acting control functions.
Mount the solenoid valve Type 3V1-06 with banjo bolt on the respective control port of the actuator.


  • Mobile: +86 150 5749 1870
  • Tel: +86 0574-56225321
  • E-mail: sales@fescolo.com
  • Fax: +86 574 5687 7923
  • Add: ROOM 1110, NO. 98 TIANGAO LANE, YINZHOU, NINGBO, CHINA

Copyright © Fescolo Pneumatic Co., Ltd.  All Rights Reserved   

sitemap